Wound Primary Current Transformer

WOUND PRIMARY CURRENT TRANSFORMER

Indotech Wound Type Current Transformers (CT) – In transformer the primary winding is composed inside the transformer. The primary winding had a single turn and connected in series with the conductor that measured the current.  

  • Capacity: There are designed to measure currents from 1 amp to 100 amps.
  • the most common one is the wound type current transformer. The wound type provides excellent performance under a wide operating range. Typically, the wound type is insulated to only 600 volts.
  • Since the load current passes through primary winding in the CT, screw terminals are provided for the load and secondary conductors. Wound Type Current Transformer are available in ratios from 2.5:5 to 100:5.
  • Wound Type Current Transformer have a primary and secondary winding like a normal transformer. These CTs are rare and are usually used at very low ratios and currents, typically in CT secondary circuits to compensate for low currents, to match different CT ratios in summing applications, or to isolate different CT circuits. Wound Type Current Transformers have very high burdens, and special attention to the source CT burden should be applied when wound CTs are used.

led as a primary conductor.

TYPE OF TRANSFORMER : WOUND PRIMARY

When the ratio is low it becomes difficult to obtain good results with the single primary turn. For that purpose wound primary CT’s are used where both primary and secondary turns are wound on the torroidal core. The ranges available are from 5/5A to 100/5A. Also Secondary 1A can be provided. Optional mounting arrangements are provided as the CT is mounted between two Bakelite plates and brass terminals are provided for connections of primary & secondary.

PRINCIPAL OF OPERATION

The standards define a voltage transformer as one in which “the secondary voltage is substantially proportional to the primary voltage and differs in phase from it by an angle which is approximately zero for an appropriate direction of the connections.”

This, in essence, means that the voltage transformer has to be as close as possible to the “ideal” transformer. In an “ideal” transformer, the secondary voltage vector is exactly opposite and equal to the primary voltage vector, when multiplied by the turns ratio

“INDOTECH” WOUND PRIMARY CURRENT TRANSFORMER’S
WOUND PRIMARY LOW TENSION TAPE WOUND CT’S WOUND PRIMARY LOW TENSION TAPE WOUND CT’S
RATED BURDEN : 15VA CLASS 1.0 SECONDARY : 1A RATED BURDEN : 15VA CLASS 1.0 SECONDARY : 5A
CT
RATIO
CODE WITHOUT    MOUNTING CODE WITH   MOUNTING CODE WITH
RESIN CAST
CT      RATIO CODE WITHOUT        MOUNTING CODE WITH
MOUNTING
CODE WITH
RESIN CAST
5/1A GW W005115B GW M005115B GW S005115B 5/5A GW W005115C GW M005115C GW S005115C
10/1A GW W010115B GW M010115B GW S010115B 10/5A GW W010115C GW M010115C GW S010115C
15/1A GW W015115B GW M015115B GW S015115B 15/5A GW W015115C GW M015115C GW S015115C
20/1A GW W020115B GW M020115B GW S020115B 20/5A GW W020115C GW M020115C GW S020115C
30/1A GW W030115B GW M030115B GW S030115B 30/5A GW W030115C GW M030115C GW S030115C
40/1A GW W040115B GW M040115B GW S040115B 40/5A GW W040115C GW M040115C GW S040115C
50/1A GW W050115B GW M050115B GW S050115B 50/5A GW W050115C GW M050115C GW S050115C
60/1A GW W060115B GW M060115B GW S060115B 60/5A GW W060115C GW M060115C GW S060115C
75/1A GW W075115B GW M075115B GW S075115B 75/5A GW W075115C GW M075115C GW S075115C
100/1A GW W100115B GW M100115B GW S100115B 100/5A GW W100115C GW M100115C GW S100115C

null

Product Design and Planning

null

Component Sourcing and Procurement

null

Testing and Quality Control

null

Final Assembly and Integration